How To Square A Miter Saw? A Step-By-Step Guide

A miter saw is an indispensable item in interior and exterior construction. The angles of the miter saw allow you to flexibly change the measurements.

You can easily adjust the angles to your liking with the adjustment unit. In this article, we will show you how to square a miter saw.

To square a miter saw, you first align a square outside the fence. You must secure both this square and the blade of the saw. You will do a square reference on the body of the blade. Then, adjust the screws and buttons to refer out of the saw table.

To ensure the highest accuracy, you should follow these steps. Discovery best miter saw under 200 for more detail

Step 1: Cleaning The Saw

Sawdust and other particles will remain on your saw after the previous use. This debris will mess up the proportions you need to align.

You need to remove sawdust and debris before you square a miter saw. In particular, this step is very important for those who do not have the habit of cleaning the saw after use.

Sawdust can get stuck in parts of the miter saw. Therefore, the best way to clean is to use an air compressor.

You use the air nozzle for the cleanest and fastest removal of sawdust. Then, you wipe the parts of the saw with a clean cotton towel. Be sure to remove any build-up when you take the next step.

Step 2: Checking The Saw Blade

You should double-check the saw blade before aligning the saw square again. Check that the saw blade is completely clean. If not, you have to wipe off the dirt and dry it. For stubborn stains, you can use detergents. Stain Remover and Boeshield’s Rust will make it easier to clean the build-up on the saw blade.

If the saw blade is dull, you should sharpen it again. You should also replace a new blade when you see that the old blade is warped or broken.

You can see that the higher the distortion, the lower the accuracy level. Therefore, if you want to square a miter saw as accurately as possible, you should change another blade to do it.

Step 3: Aligning The Table

Most miter saw users place them on the saw table. Fixing the saw to the saw table makes it easier for you to perform sawing and cutting jobs.

However, the saw table will command to go after a period of use. Therefore, you need to adjust the saw table to be flat. Measurement with the naked eye will lack accuracy.

The most standard way of measuring flatness is to use a straight edge device. You just need to put this device on the saw table and it will do the measurement for you.

If the proper straight is off, your saw has been ordered to go. You have to adjust it by replacing the wood surface of the saw table. You can also insert a small wedge onto its surface to re-create flatness.

Step 4: Aligning The Fence

The fence is the part located at the back of the table. This part has the effect of fixing the materials when you cut. If you want to square a miter saw, you need to square the fence for your saw. You must align the edges of the fence to align.

Using a winning edge device will make it easier for you to find non-square points. Your job is to place this device along the length of the fence.

When you notice the fence needs adjusting, loosen the screws first. Then, adjust the edges of the fence as desired. After the adjustment is complete, remember to tighten the screws. The two sides of the fence must be independently perpendicular to each other.

Step 5: Adjusting The Miter Angle

First, you need to adjust the bevel of the saw blade to a 0-degree angle. You must ensure that the angle Miter has set perpendicular to the fence.

After that, you just adjust the Miter angle to 0 degrees. Place a square on top of the saw so that one side of the square rests against the front edge of the fence. Next, you set the saw to the lowest possible position. Push the square to the side of the saw blade.

Only when you raise the guard of the saw blade can you push the square close to the saw blade. You must fix one side of the square to the fence and the other side to the saw blade.

Now you have to check if there is any gap between the saw blade and the fence. If so, loosen the knob and adjust then tighten it again. Adjust the tilt angle to a right angle by loosening the screws of the compartments.

Step 6: Adjusting The Bevel

First, you need to adjust the bevel of the saw blade to a 0-degree angle. You must ensure that the angle Miter has set is perpendicular to the fence.

After that, you just adjust the Miter angle to 0 degrees. Place a square on top of the saw so that one side of the square rests against the front edge of the fence.

Next, you set the saw to the lowest possible position. Push the square to the side of the saw blade. Only when you raise the guard of the saw blade can you push the square close to the saw blade. You must fix one side of the square to the fence and the other side to the saw blade.

Now you have to check if there is any gap between the saw blade and the fence. If so, loosen the knob and adjust then tighten it again. Adjust the tilt angle to a right angle by loosening the screws of the compartments.

Step 7: Checking The Accuracy Level

After you have everything adjusted, you need to check the accuracy of the saw. Let’s cut a piece of wood. Use a square to see if it’s square. If not, you must redo the adjustment steps.

Conclusion

The above is a detailed guide to square a miter saw. We hope that this information will make working with your saw easier.

Thank you for reading!